MTG Truck Shops — Mobile Transportation Group Inc
Annual DOT Inspections
The annual DOT inspection is the one document a roadside officer will ask for and the one deadline that does not move. MTG Truck Shops performs annual inspections under 49 CFR 396.17 at our four shops and at fleet yards across Colorado, Wyoming and Texas, and hands back a per-unit report you can file and carry.
Annual DOT inspection
Federal rules require every commercial motor vehicle in a motor carrier's operation to pass a periodic inspection at least once every 12 months. That periodic inspection is what the industry calls the annual DOT inspection, and it applies to the power unit whether the truck runs one state or forty. A unit that has been repaired after being placed out of service can also need a fresh inspection before it goes back to work, so the annual date is a floor rather than a full maintenance plan.
The inspection has to be performed by a qualified inspector. 49 CFR 396.19 sets out who qualifies: someone who has been trained and can demonstrate the knowledge and ability to inspect the parts and accessories the inspection covers. Every MTG inspector works to that standard, in the shop or in your yard, and signs the report for the unit.
The paperwork matters as much as the wrench work. The inspection report must be kept for 14 months, and proof that the unit passed has to be on the vehicle — a copy of the report or the inspection record travelling with the truck. MTG issues a report per unit so the fleet office keeps its 14 months of records while the driver carries the copy that gets checked at roadside.
What we check
The annual inspection covers the parts and accessories listed in the federal standard, not a quick visual pass. These are the systems we work through on each unit, and what we are actually looking for in each one.
Brakes and air system
Linings, drums and rotors, slack adjusters and pushrod travel, air lines, the compressor and governor, and the low-air warning. We check for leaks at the fittings and look for the spring brakes holding, with the ABS lamp behaving the way it should.
Steering
Steering wheel free play, tie rod ends, drag link, kingpins, the steering gear box and power steering leaks. Anything with play, binding or a fresh leak is written up before it becomes a steering complaint on the road.
Suspension
Leaf springs, hangers, shackles and U-bolts, air bags and ride height, torque rods and shock absorbers. Cracked leaves, missing U-bolt nuts and a bag that will not hold air all fail the same way at roadside.
Frame
Frame rails, cross members, welds and fasteners, plus the fifth wheel mounting. We look for cracks, rot, loose or missing bolts and any repair that has started to fail, because frame defects escalate quickly under load.
Tires and wheels
Tread depth, sidewall damage, dual matching and inflation, then lug nuts, studs, rims, hubs and wheel seals. A leaking seal or a cracked rim is cheaper to catch in the bay than on the shoulder with a trailer down.
Lighting
Headlamps and aim, turn signals, brake lamps, clearance and marker lamps, reflectors, trailer wiring and the electrical cord. A single dead marker lamp is a common reason a unit gets pulled in for a fuller look.
Coupling devices
Fifth wheel jaws and locking, mounting bolts and safety latches, the trailer kingpin, gladhands, air lines and the electrical cord. Coupling failures are infrequent and serious, so this section gets a hands-on check rather than a glance.
Exhaust
Manifold, pipes, hangers, turbo and stack condition, with attention to leaks and to anything routing exhaust where it should not go. Loose hangers and cracked pipes are the usual findings on high-mileage tractors.
Fuel system
Tanks, straps, caps, lines, filters, visible leaks and fuel pressure where it can be read. A weeping line or a chafed hose is a fire risk, not a maintenance item to schedule for later.
Windshield and wipers
Cracks in the wipe path, wiper blades and arms, washers, mirrors, the defroster and cab glass. Visibility items get written up because officers inspect them on every level of roadside check.
Findings are written up as they come, with the defect, the location on the unit, and whether it is a repair now or a watch item. Nothing is hidden behind a pass or fail — a fleet that knows which three units are two months from a brake job can plan for it instead of paying for a roadside tow.
Pre-inspection before a roadside check
A roadside inspection is not the moment to discover a chafed air line. Our pre-inspection checks a unit against the same standard roadside officers work from, so the obvious defects get fixed in the bay instead of being written up on the shoulder with a driver standing in traffic.
To be precise about who does what: CVSA inspections are enforcement inspections, performed by certified enforcement officers at roadside or at an inspection station, and CVSA decals are issued through that program alone. A Level I is the full vehicle inspection, a Level II is a walk-around with selected items, and a Level III is a driver credentials check — not a vehicle repair. MTG performs annual DOT inspections and pre-inspections to CVSA Level I standards. We do not perform CVSA inspections and we do not issue CVSA decals.
For a fleet facing a compliance review, the pre-inspection is the cheaper half of the work: fix the defects that count against you, keep the reports that prove you looked.
Onsite fleet inspections
Mobile inspection is the default for fleets because it removes the deadhead. We come to your yard, terminal or jobsite with the inspection equipment and work through the unit list in the order that keeps your operation moving — the units going out tonight first, the parked ones after.
The annual DOT inspection is combined with a PM service in the same visit wherever the schedule allows: oil and filters, chassis lubrication, brake adjustment, tire pressures and a walk-around, with the inspection report written against the same unit. One visit, one set of records, one invoice.
You receive a report for every unit inspected, a consolidated list of defects across the fleet, and a recommended repair list in priority order. Records are provided as documents you can file, not as notes on a technician's phone. Onsite programs run under the same preventive maintenance structure described on the preventive maintenance page, and the repair scope is covered on our capabilities page.
What to have ready
Three things make an inspection visit run on schedule: the unit numbers, the last inspection report, and an honest list of what is already known.
The list of trucks and trailers to inspect, in the order you want them done.
The previous annual inspection for each unit, so the 12-month clock and the open items carry forward.
Faults already reported by drivers — warning lights, air leaks, brake complaints — so they are checked first.
Access details save the same kind of time: gate codes, yard hours, where keys are kept and whether the unit can be moved. If a trailer is loaded or dropped, say so when you book, because it changes how the inspection is sequenced.
